200M 400M 200M
RNG: 2.4 KM
BRG: 047°
ALT: 3,200 FT
SPD: 480 KTS
HDG: 012° N
TGT: ALPHA-7
MODE: SEARCH
PWR: NOMINAL
FREQ: X-BAND
STATUS: LOCK
NAVTGTWPNDEFRDRCOM
MIL-STD-1553IFF: ACTIVELINK-16: SYNC
SECTOR: ALPHA
THREAT: CLEAR
RADAR: ACTIVE
TRACK: 6 TGT
LAT 28.6213°N LON 77.3873°E
NX
Neometrix Target Acquired
GB Flag English
English Flag English
Indian Flag हिन्दी
Francis Flag Français
Dutch Flag Deutsch
Spanish Flag Español
Arabic Flag العربية
Russian Flag Русский
Japanese Flag 日本語
Portuges Flag Português
Italian Flag Italiano
Israel Flag עברית
Chinese Flag 中文
Korean Flag 한국어
Thailand Flag ไทย
Vietnamese Flag Tiếng Việt
Indonesia Flag Bahasa Indonesia
Malasia Flag Bahasa Melayu
Kiswahili Flag Kiswahili
Ethiopia Flag አማርኛ
isizulu Flag isiZulu
Hausa Flag Hausa
    Neometrix / Rail Test Equipment / Brake Cylinder Test Bench / NMX-BCS-115
    NMX-BCS-115 · ENGINEERED-TO-ORDER CLASS — DUTY · FIXTURE AND REACTION · AIR AND RAMP · FORCE AND STROKE · THE ADJUSTER · BUILD · PROVE

    Brake Cylinder Test Bench. Take up the wear, nothing else.

    A bogie-mounted brake cylinder carries its own slack adjuster. A pawl and ratchet lengthen the piston when the stroke runs past its set value, so that the brake shoe stays close to the wheel as it wears. Neometrix engineers the bench that proves such a cylinder as a part: its leakage, its force, its stroke and its adjuster.

    So the bench has to know that the adjuster must take up the wear and nothing else, hold the cylinder as it sits on the bogie, and read the force and the stroke together.

    A brake cylinder test bench on a plain white studio background: a stiff pale grey welded steel bench frame with a rounded-end pale grey brake cylinder held horizontally at its left end by a clamp, two thin black hoses from the cylinder to a small pale grey valve block under the frame, a bright steel piston rod running through a short bright steel force cell to a pale grey reaction unit that holds a bright steel coil spring, a pale grey stepped stop block with four steps on a slide rail beside it, a plain pale grey control cabinet at the right, and no people
    Fig · 01 — A brake cylinder test bench: the cylinder in its fixture, a force cell, a reaction unit and a stepped stop, and a cabinet — illustrative render.
    The leakage
    is read in both positionswith the piston at rest and fully out
    The force
    is read up and downfriction shows as the gap between the two
    The stroke
    is measured every timeit is the signal the adjuster works from
    The adjuster
    is shown at worka stepped stop stands in for wear
    Status
    engineered to orderno delivery is claimed
    ISO 9001ISO 14001Test conditions set by the customer and the brake maker
    01
    Overview

    What a brake cylinder test has to get right, and what goes wrong when it does not.

    A cylinder can hold its air, push with the right force and still brake badly, because its adjuster takes up the wrong slack, or none at all.

    A bogie-mounted brake cylinder and its adjuster parts on a plain white studio background: a pale grey cylindrical brake cylinder lying with a rounded end cap on the left, a bright steel piston rod from its right end, a pale grey ring with a regular row of small teeth around the body near the rod end, a bright steel cap screw with a plain thread and a small bright steel coil spring lying in front, and no people
    Fig · 02 — A brake cylinder with its adjuster parts: the cylinder, a ratchet ring, an adjusting screw and a return spring — illustrative render.

    Take up the wear, nothing else.

    What the bench is for

    It holds a brake cylinder as it sits on the bogie, applies air in a controlled ramp, and records the leakage, the force and the stroke. It also shows what the slack adjuster does as the stroke grows.

    Why the adjuster is part of the cylinder

    On a bogie-mounted brake each cylinder sits close to its brake unit and carries its own adjuster, so the cylinder and the adjuster are proved together.

    How the adjuster works

    When the stroke runs past a set value, a pawl turns a ratchet by one tooth, and the piston becomes longer on its return, so that the next stroke is shorter.

    Why wear and nothing else

    A stroke is made of three things: the gap the brake has to close, the stretch of the brake unit under load, and wear. The adjuster should take up the slack that wear opens and leave the rest alone.

    What goes wrong if it does not

    An adjuster that moves on a hard application over-adjusts, and the shoes sit too close to the wheel. One that never moves lets the stroke run out. Both look fine on a leak test.

    Why the force is read up and down

    The force is the pressure times the area, less the return spring and the friction of the seals. Friction does not show on a rising reading alone. It shows as the gap between the force on the way up and the way down.

    Why the leakage is read in two positions

    A seal can behave differently with the piston at rest and with it fully out, so the leakage is read in both positions, and not once.

    Why a stepped stop

    Wear is stood in for by a stop that moves away in steps. At each step the cylinder applies and releases, and the bench records the length of the piston. So you see how many applications the adjuster needs, and that it does not move when it should not.

    Why a cylinder bench is not another bench

    It is not a distributor valve test bench, which proves the valve that feeds the cylinder, and not a coach and rake test rig, which proves a whole coach or rake. It tests the cylinder and its adjuster as a part.

    02
    The method

    Duty, fixture and reaction, air and ramp, force and stroke, the adjuster, build and prove.

    Six steps in a fixed order. The wear stepper and the blank run are the two that a quick job skips.

    1 · Duty

    The cylinder types, how each is mounted, the adjuster type, the pressures and strokes that matter, how many cylinders a day, the room and the services, are noted.

    2 · Fixture and reaction

    A stiff frame holds the cylinder as it sits on the bogie. A reaction unit gives it a stop and a spring, so that the cylinder meets a gap and a stretch as it would on the brake unit.

    3 · Air and ramp

    Clean dry air is applied through a regulator and a ramp valve, so that the pressure rises and falls at a rate that is the same every time.

    4 · Force and stroke

    A force cell in the load line and a stroke sensor on the piston record the force and the stroke together, so that the force is known at every point of the stroke, up and down.

    5 · The adjuster

    A wear stepper moves the stop away in steps, and a controller applies and releases at each step, so that the bench shows the adjuster taking up the wear and leaving a normal stroke alone.

    6 · Build and prove

    The bench is built and leak tested, a blank run is made, the force cell and the transducers are checked against references, every guard is tried, and the record goes with the bench.

    Which fault, which safeguard

    What can go wrongWhy it happensWhat the bench does about it
    A cylinder passes though a seal leaksthe leakage was read in one position onlythe leakage is read with the piston at rest and fully out, against a reference
    The adjuster creeps with every applicationit moves on a stroke that is normal, or on the stretch of a hard applicationhard and normal applications at a normal stroke, with the length of the piston recorded to show that it does not change
    The adjuster never takes up the wearthe pawl does not engage, or the ratchet is stiff or seizedthe stop is stepped away, and the bench counts the applications the adjuster needs for each step
    The force is wrong for the pressurethe return spring is wrong, or the seals are tightthe force is read against the pressure on the way up and on the way down, and the gap between them is recorded
    The piston returns slowly or not fullythe return spring is weak or the friction is highthe release is timed and the return position is recorded after every application
    The stroke reads wronglythe stroke sensor drifted, or was never checkeda gauge block check and a zero at the start of each run
    A good cylinder is damaged by the testthe pressure rose too fast, or the piston struck its enda controlled ramp and a soft stop at each end
    Someone is hurt by stored energythe return spring and the air hold energy while the cylinder is clampeda guard round the fixture, a relief valve on the air circuit, and a procedure that says nobody reaches in while the cylinder is charged

    The step people underrate is the wear stepper. A bench that never moved the stop cannot say whether the adjuster works, only that the cylinder does not leak.

    03
    Work content

    What the bench contains, element by element.

    Read it as a checklist: a bench missing a row will still pressurise a cylinder and read a force, but it will not show what its adjuster does.

    The wear stepper and reaction unit of a brake cylinder test bench on a plain white studio background: a pale grey stepped stop block with four clear steps on a bright steel slide rail, a short bright steel cylindrical force cell, a bright steel coil spring running to a pale grey cylindrical tube, all on a flat pale grey base plate, and no people
    Fig · 03 — The wear stepper and reaction unit: a stepped stop that stands in for wear, and a spring that stands in for the stretch — illustrative render.
    ElementWhat it doesWhat matters
    Frame and fixturehold the cylindera stiff frame and a clamp that hold the cylinder in the attitude it has on the bogie, with room for its fittings
    Reaction unitstands in for the brake unita stop that gives the gap and a spring that gives the stretch, so that the cylinder meets what it meets on the bogie
    Wear stepperstands in for weara stop that moves away in clear steps, set from the controller, so that wear is added a step at a time
    Air supply and regulatorfill the cylinderclean dry air through a regulator, so that the supply is steady and the same every time
    Ramp valveraises and lowers the pressurea valve that ramps the pressure up and down at a set rate, so that the force can be read both ways
    Pressure transducerreads the pressurea transducer on the cylinder port, checked against a reference, and read with every application
    Force cellreads the forcea cell in the load line, checked against a reference, and read with the stroke
    Stroke sensorreads the piston positiona sensor fine enough to see one step of the ratchet, with a zero check at the start of each run
    Leakage circuitreads the leakagea circuit that holds the pressure with the piston at rest and fully out, and reads the decay against a reference
    Controller and loggerrun the sequencea sequence that applies, releases, steps and records, with the rule and the limits set by the customer, and a log of every run
    Guards and reliefprotect peoplea guard round the fixture, a relief valve on the air circuit, and a vent that is safe to open
    Testing & documentationprove the bench firsta leak test, a blank run, the force cell and the transducers checked against references, every guard tried, and a record the customer can inspect

    The elements that decide the result are the reaction unit and the wear stepper. The first gives the cylinder a gap and a stretch to meet, and the second adds wear a step at a time.

    Full specification — expand
    SystemA stiff frame and a fixture that holds the brake cylinder as it sits on the bogie; a reaction unit with a stop and a spring that stand in for the gap and the stretch of the brake unit; a wear stepper that moves the stop away in steps; an air circuit with a regulator, a ramp valve and a pressure transducer; a force cell in the load line and a stroke sensor on the piston; a controller and logger that apply, release, step and record; a guard and a relief valve; and a leak test, a blank run and documentation before handover
    The One IdeaTake up the wear, nothing else.
    What A Stroke Is Made OfThe gap the brake has to close, the stretch of the brake unit under load, and wear. The adjuster should take up the slack that wear opens and leave the rest alone
    Why The Force Is Read Up And DownThe force is the pressure times the area, less the return spring and the friction of the seals. Friction shows as the gap between the force on the way up and on the way down
    StandardsNo test standard is quoted here. The conditions to be reproduced are stated by the customer and the brake maker, and approval of a cylinder or an adjuster rests with the customer and the authority they name; none is claimed here. No certification or accreditation is claimed here
    ConfigurationsA cylinder bench, an adjuster endurance rig, and a production and overhaul bench
    Scope BoundaryThis page is the brake cylinder test bench, which tests the cylinder and its adjuster as a part. It is not a distributor valve test bench, which proves the valve that feeds the cylinder (see distributor valve test bench), not a coach and rake test rig, which proves brake equipment on a whole coach or rake (see single wagon, coach and rake test rigs) and not a bogie test rig, which proves a whole bogie (see bogie test rig and turntable). It does not certify a cylinder, and it does not replace the operator's own judgement
    StatusNeometrix has quoted against successive brake cylinder and slack adjuster test bench requirements, and no delivered brake cylinder test bench is claimed.
    04
    Configurations

    One method, three ways to build the bench.

    The method, the wear stepper and the blank run are shared. What changes is how long each cylinder stays on the bench, and how many are proved in a day.

    Cylinder bench

    Leakage, force and stroke

    For proving a cylinder as a part. A fixture and a reaction unit hold it, a ramp valve moves the air, and a force cell and a stroke sensor read the force and the stroke, with the leakage read in both positions.

    Adjuster endurance rig

    Many applications, a count

    For showing what the adjuster does over a long time. A wear stepper moves the stop away at set intervals. A controller applies and releases many times and counts the adjustments, so that creep and failure to adjust both show up.

    Production and overhaul bench

    Two stations, a record

    For a shop that proves cylinders every day. Two stations let one cylinder be clamped while the other is tested, with a record for every serial and a pass or fail decided by the customer's own limits.

    And the part that is not equipment at all, yet decides all three: the limits. The pressures, forces, strokes and counts come from the customer's duty and the brake maker, not from the bench.

    05
    The drawings

    A reference set, drawn as real CAD sheets.

    Two sheets of one reference configuration: the arrangement of a brake cylinder test bench with three details, and its signal and command chain with the curves that show why an adjuster must take up the wear and nothing else. They show the cylinder in its fixture, the load line with its force cell, the stepped stop that stands in for wear and the air circuit. They carry tags and letters only. Every pressure, force, stroke and count is fixed by design for the customer's cylinders.

    Reference drawing sheet one, the arrangement and details of a brake cylinder test bench. An elevation shows a frame holding a brake cylinder with its adjuster ring clamped horizontally, the piston rod running through a force cell to a stepped stop on a vertical slide driven from above by a wear stepper, a reaction spring on the right-hand upright, a stroke sensor beside the rod, a valve block with a hose to the cylinder port, and sensor cables to a control cabinet that holds a controller and a logger. Detail A shows the cylinder in section, with its piston, return spring, right cover, rod, ratchet ring, pawl, air port and the stroke. Detail B shows the stepped stop, a stair whose faces set the gap in front of the rod end, with up for less wear and down for more. Detail C shows the air circuit: a supply, a regulator, a ramp valve, the cylinder, a pressure transducer and a relief valve. An item list numbers eight parts. A title block stamped reference configuration, not for construction
    Fig · 04 — Sheet 01, the arrangement: the bench with the cylinder in its fixture, the cylinder in section, the stepped stop and the air circuit. Reference configuration, letters only.
    Reference drawing sheet two, the chain and the curves of a brake cylinder test bench. A chain of boxes shows a force cell, a stroke sensor and a pressure transducer feeding signal inputs, a controller with its rules and limits, a logger and a record for every serial, and the command side in which the controller drives a ramp valve and a wear stepper while a guard and relief stops the air and the stepper. Detail A is a computed plot of stroke against the number of applications: the stroke rises with the wear until it passes a set value and then falls back by one step each time, so that it stays in a narrow band, while without an adjuster it rises for ever. Detail B is a computed plot of force against pressure on the way up and on the way down for good seals and for tight seals, in which friction shows as a wider gap between the lines. Detail C is a computed plot of the normal stroke against the number of applications when every fifth application is hard, in which a set value above the stretch leaves the stroke alone and a set value below it takes a step off after each hard application, so that the shoes sit closer than designed. A title block stamped reference configuration, not for construction
    Fig · 05 — Sheet 02, the chain and the curves: the measurement path and the commands, the adjuster at work, the force up and down, and a hard application. Reference configuration, tags only.

    Every real bench is drawn for its own cylinders, its own adjusters and its own room. These sheets are the arrangement and the order of working that a project set starts from. Approval of any drawing rests with the customer and the authority they name; none is claimed here.

    06
    Where it is used

    Wherever a brake cylinder carries its own adjuster, and has to be proven before it goes back on the bogie.

    The common thread is a cylinder that will work for years without anyone adjusting it, and a test that has to show that it will.

    Rail workshops

    Where cylinders come off bogies at overhaul, and each one is proven before it is fitted again.

    Coach and train-set builders

    Where new cylinders arrive in sets and every one is shown to hold its air and to adjust before the bogie is assembled.

    Brake makers

    Where a new design, or a change of seal or spring, has to be shown to push with the force it was drawn for and to take up wear without creeping.

    Brake development groups

    Where the effect of a stroke, a stretch or a pressure on the adjuster is measured and not assumed.

    07
    Watch

    See it in motion.

    A short walkthrough video of the brake cylinder test bench.

    08
    FAQ

    Common questions.

    Longer answers, for readers who want the reasoning.

    Q · 01 What does a brake cylinder test bench actually do?
    It proves that a brake cylinder, with its own slack adjuster, does what it should. A fixture holds the cylinder as it sits on the bogie, and a reaction unit gives it a stop and a spring to meet. A ramp valve raises and lowers the air pressure, a force cell and a stroke sensor read the force and the piston position together, and a leakage circuit reads the decay with the piston at rest and fully out. In another run a wear stepper moves the stop away in steps, and the controller applies and releases at each step, so that the bench can show how the adjuster takes up the wear. A logger keeps every run. The bench does not choose the test. That comes from the customer's own duty and the brake maker, and the bench is built, proved and recorded to carry it out.
    Q · 02 Why must an adjuster take up the wear and nothing else?
    Because the stroke of a brake is made of more than wear. The brake has to close a gap before the shoe touches the wheel, and then the brake unit stretches under load, so a hard application makes a longer stroke than a gentle one even when nothing has worn. An adjuster that follows the whole stroke can mistake that stretch for wear, move a step, and leave the shoes a little closer to the wheel than the design intends. An adjuster that does not move at all lets the real wear build up until the piston runs out of stroke. Both can pass a leak test and a force test. Only a test that adds wear in known steps, and also applies hard at a normal stroke, shows which one the adjuster is.
    Q · 03 Why read the force on the way up and the way down?
    Because the two readings differ, and the difference is the friction of the seals. The force a piston gives is the pressure times its area, less the return spring and the friction. On a rising pressure the friction holds the force back, and on a falling pressure it holds the force up, so the two lines run parallel with a gap between them. A cylinder whose seals are too tight shows a wide gap, and one with worn seals shows a narrow one. A single reading on the way up cannot tell a tight seal from a weak spring, and the gap can. The bench ramps the pressure at a set rate so that the two lines are comparable from one cylinder to the next.
    Q · 04 Why a stepped stop, and what does the count tell you?
    Because wear cannot be waited for. A real brake takes months to wear a block, and a bench cannot wait. A stop that moves away in steps adds the wear in known amounts. At each step the controller applies and releases the cylinder and records the length of the piston after each application, and the count of applications the adjuster needs to take up the step is the result. A good adjuster takes up each step within a few applications and then stays still. One that creeps keeps moving after the step is taken up, and one that is stiff does not move at all. The adjuster endurance rig repeats this many times and counts every adjustment, because a fault that shows only now and then is still a fault.
    Q · 05 Is this the same as a distributor valve bench, a coach and rake rig or a bogie rig?
    No, and the differences are worth stating precisely. The distributor valve test bench page covers the bench that proves the valve which feeds the cylinder. The single wagon, coach and rake test rigs page covers rigs for brake equipment at the level of a whole coach or rake. The bogie test rig and turntable page covers equipment that proves a whole bogie. This page is the bench that tests the brake cylinder and its slack adjuster as a part. It does not replace any of them, and it does not claim what they claim a second time.
    Q · 06 Has Neometrix built one of these?
    We would rather answer this plainly than let a page imply otherwise. Neometrix has quoted against successive brake cylinder and slack adjuster test bench requirements, and no delivered brake cylinder test bench is claimed. What stands behind the offer is adjacent: the pages for the distributor valve test bench, the coach and rake test rigs and the bogie test rig each describe equipment that holds a rail part at pressure and watches the result, and each states its own status. The pressure transducers, the force cell, the stroke sensors, the valves and the logger chassis are catalogue items, bought in, not invented. What Neometrix engineers is the bench around them: the frame and the fixture, the reaction unit and the wear stepper, the air circuit, the guards and the proof. So the honest position is that the bench is engineered to order, the neighbouring disciplines are in the building, and the first bench of this exact kind will be built around the customer's own cylinders rather than taken off a shelf.
    Q · 07 Which standard applies, and what can the bench not do?
    No test standard is quoted on this page. Brake makers and rail authorities publish their own conditions, and the customer states the ones the bench is to reproduce: the pressures, the forces, the strokes, the steps of wear and the limit on the count. The bench makes a cylinder's behaviour visible and records it. It does not certify a cylinder, it is not a distributor valve bench and not a rig for a whole coach, and it does not replace the operator's own judgement about who is near a charged cylinder and when. This page claims no certification or accreditation. No pressure, force, stroke, count or time figure is printed here, and approval of a cylinder or an adjuster rests with the customer and the authority they name; none is claimed here.
    Q · 08 What do you need from us to quote?
    Six things, and most of them describe your cylinders rather than the bench. First, the cylinders: which types, how each is mounted and whether the adjuster is built in. Second, the conditions: the pressures, forces and strokes that matter, and the limits on leakage. Third, the adjuster test: the steps of wear, and what counts as taking them up. Fourth, the throughput: how many cylinders a day, which decides the number of stations. Fifth, the room: what services it has and how much space there is. Sixth, the record: whether a blank run and a record for each serial are needed. From that we come back with a bench concept, a proving plan you can check, and a budgetary price.
    09
    Related

    The neighbouring pages, and how they differ from this one.

    Three neighbours: one proves the valve that feeds the cylinder, one proves a whole coach or rake, one proves a whole bogie.

    Browse all Neometrix product lines.

    Get a quotation

    Tell us the cylinder,
    and what its adjuster must do.

    The projects desk replies within two working days with a bench concept, a proving plan you can check, and a budgetary quotation. Write to [email protected] or use the form.

    Enquire — brake cylinder test bench Capability sheet (PDF) +91 7777 876 876
    ISO 9001 / 14001 ENGINEERED-TO-ORDER CLASS — BRAKE CYLINDER TEST BENCH DUTY · FIXTURE AND REACTION · AIR AND RAMP · FORCE AND STROKE · THE ADJUSTER · BUILD · PROVE — TAKE UP THE WEAR, NOTHING ELSE. ENGINEERED IN NOIDA · INDIA

    Trending Products

    Share This Page

    Engineered To Standards Used In UK, NATO & U.S. Defence Procurement
    DEF STAN (UK MoD)
    NATO STANAG
    RTCA/EUROCAE DO-160
    MIL-SPEC / MIL-STD
    Address
    E-148, Sector-63, Noida, Delhi-NCR, India
    Phone
    Email
    Working Hours
    8:30 AM – 5:30 PM  ·  Mon – Sat
    move to top arrow