200M 400M 200M
RNG: 2.4 KM
BRG: 047°
ALT: 3,200 FT
SPD: 480 KTS
HDG: 012° N
TGT: ALPHA-7
MODE: SEARCH
PWR: NOMINAL
FREQ: X-BAND
STATUS: LOCK
NAVTGTWPNDEFRDRCOM
MIL-STD-1553IFF: ACTIVELINK-16: SYNC
SECTOR: ALPHA
THREAT: CLEAR
RADAR: ACTIVE
TRACK: 6 TGT
LAT 28.6213°N LON 77.3873°E
NX
Neometrix Target Acquired
GB Flag English
English Flag English
Indian Flag हिन्दी
Francis Flag Français
Dutch Flag Deutsch
Spanish Flag Español
Arabic Flag العربية
Russian Flag Русский
Japanese Flag 日本語
Portuges Flag Português
Italian Flag Italiano
Israel Flag עברית
Chinese Flag 中文
Korean Flag 한국어
Thailand Flag ไทย
Vietnamese Flag Tiếng Việt
Indonesia Flag Bahasa Indonesia
Malasia Flag Bahasa Melayu
Kiswahili Flag Kiswahili
Ethiopia Flag አማርኛ
isizulu Flag isiZulu
Hausa Flag Hausa
    Neometrix / Rotorcraft Structural Test Facilities / Rotor Hub and Blade Test Facility / NMX-RBH-107
    NMX-RBH-107 · ENGINEERED-TO-ORDER CLASS — DUTY · FRAME AND FIXTURES · ACTUATORS AND POWER · CONTROL · TRIPS · BUILD · PROVE

    Rotor Hub and Blade Test Facility. Tension changes the twist.

    A rotor hub and blade test facility loads a helicopter blade root, a tension-torsion element or a hub plate the way the rotor loads it in flight, and watches how it stiffens, how it moves and how long it lasts. A stiff frame holds the specimen and servo-hydraulic actuators load it. Neometrix engineers it as a facility: the frame, the fixtures, the actuators, the control, the trips and the proof.

    So the facility has to know that tension changes the twist, hold the pull as a force while the specimen twists, and load every channel together, not one at a time.

    A rotor blade root test facility on a plain white studio background: a long, low pale grey steel reaction frame with a thick upright end block at each end and a tall gantry arch in the middle, a short tapering dark grey blade root section clamped at the left end block in a heavy bright steel root fixture, a large pale grey hydraulic cylinder with a bright rod joined on the same axis to its free end and fixed to the right end block, a bright steel torque arm at the free end joined to a smaller vertical hydraulic cylinder, a third hydraulic cylinder pointing down from the gantry arch, black hoses running to a small manifold block on the frame, and no people
    Fig · 01 — A rotor blade root test facility: a stiff reaction frame, a blade root section clamped at one end, and hydraulic cylinders that pull it along its axis, twist it with a torque arm and press on it from above — illustrative render.
    The tension
    is a force, held steadythe pull of the blade, set by the rotor speed
    The twist
    rides on the tensiona strap twists more stiffly under the pull
    The bending
    flap and lead-lag, cycledtogether with the pull and the twist
    The frame
    carries every loadstiff, so no load or motion is lost
    Status
    engineered to orderno delivery is claimed
    ISO 9001ISO 1400114 CFR 29.571 reference for fatigue tolerance of rotorcraft metallic structure
    01
    Overview

    What a rotor test has to get right, and what goes wrong when it does not.

    Because each load is easy to name, and the way they act together is the part that decides.

    A rotor hub plate test rig on a plain white studio background, seen from slightly above: a wide flat pale grey steel square base frame, a thick bright steel plate shaped like a four-armed cross with a large round central hole on a short central pedestal, and four pale grey hydraulic cylinders with bright rods lying flat and pointing outwards, each joined by an adapter and a link to one arm of the plate and fixed at its outer end to the frame, with black hoses, and no people
    Fig · 02 — A hub plate test rig: a four-armed plate on a central pedestal, with a hydraulic cylinder pulling each arm outwards against the frame — illustrative render.

    Tension changes the twist.

    What the facility is for

    It loads a blade root, a tension-torsion element or a hub plate the way the rotor loads it in flight. It finds out how the part stiffens, how it moves and how long it lasts, on the ground, where a failure costs a specimen and not a helicopter.

    Why tension changes the twist

    A tension-torsion strap joins the blade to the hub. It carries the pull of the blade in tension, and it twists to let the blade change its pitch. The pull stiffens the strap in torsion, so the same twist needs more torque under more tension. A strap twisted with no tension is a different part from one twisted under the pull.

    Why the pull is held as a force

    In the rotor the pull is a force, set by how fast the rotor turns. When a strap twists, its ends draw closer and the pull stays where it was. A test that holds the ends still does something else: each twist stretches the outer edges of the strap, and the pull climbs. So the tension runs in force control, and the twist is driven on top of it.

    Why the loads act together

    In flight the blade root sees the pull, flap bending, lead-lag bending and pitch twist together. They are not independent, because the pull changes how the part bends and twists. So the facility applies them together, with channels that are phased against one another and that follow the spectrum of the flight.

    What the tests are

    A static test finds the stiffness and the strength. A fatigue test cycles the loads at a set level, and counts the cycles to the first crack. A spectrum test follows a recorded sequence of loads, flight after flight, with inspections between the blocks.

    Why a hub plate is different

    A hub plate carries the pull of every blade at once, and it sees the flap and lead-lag moments of each. A hub plate rig loads the plate through arms that stand in for the blades, so the loads come from the arms and not from a single axis.

    Why the frame matters

    The reaction frame carries every load that the actuators apply. Any give in it shows up as lost load or lost motion. A stiff frame with a short load path lets the actuators do what they are told.

    Why a rotor facility is not for every job

    It proves a blade root, a strap or a plate. It does not spin a rotor, and it does not test the actuators that control the pitch. The duty states the specimen, the loads and the spectrum, and the facility is built for that.

    02
    The method

    Duty, frame and fixtures, actuators and power, control and trips, build and prove.

    Six steps in a fixed order. The control and the trips are the two that a quick job skips.

    1 · Duty

    The specimen, the loads, the spectrum, the channels and the cycles in a day are noted, with the room and the services it has.

    2 · Frame and fixtures

    The reaction frame, the root fixture and the adapters are matched to the specimen, so that it is held and loaded on its own axis, and nothing in the load path gives.

    3 · Actuators and power

    The actuators, the servo valves and the power pack are matched to the loads and to the speed of the cycle, and the power has margin for the busiest channel.

    4 · Control

    The controller runs every channel together, with load-cell feedback, phasing between the channels and the spectrum, and the tension runs in force control.

    5 · Instruments and trips

    Load, displacement and strain are measured, and trips on load, displacement and stiffness are set, so that a change in the specimen ends the run.

    6 · Build and prove

    The frame is built and aligned, the load cells are calibrated, a proving specimen is run in steps, every trip is tried, and the record goes with the facility.

    Which fault, which safeguard

    What can go wrongWhy it happensWhat the facility does about it
    The pull climbs with every twistthe ends are held still, so twisting the strap stretches its outer edgesa tension channel in force control: the pull is held, and the ends are free to draw closer as the strap twists
    The twist reads too softit was measured with no tension, or with the wrong tensiona twist measured under the set tension, with load cells that are calibrated
    Load or motion is lostthe frame or a fixture gives under loada stiff frame, a short load path, and fixtures that are tried before the test
    The channels fight each otheractuators act on one specimen with no phasingchannels that are phased against one another, and one controller that sees all of them
    The specimen is loaded off its axisthe root is held, or an adapter is fitted, out of lineroot fixtures and adapters aligned at the build and checked after
    The run goes on past a cracka crack grows between inspections, and the stiffness fallsa trip on stiffness and displacement that ends the run, and a check between blocks
    The hydraulic power dropsa pump or a filter fails in the middle of a runa power pack with margin, filters that are watched, and a controlled stop that leaves the specimen safe
    Someone is near a loaded specimena guard is opened while the part is under loadguards and interlocks, a control room outside, and a procedure that says nobody stands near a loaded specimen

    The step people underrate is the force control of the tension. A facility looks the same whether its pull is held as a force or follows the position of the ends.

    03
    Work content

    What the facility contains, element by element.

    Read it as a checklist: a facility missing a row will load a specimen, but it will not tell you what the loads really were.

    A tension-torsion strap test fixture on a plain white studio background: a flat pack of thin bright steel strap leaves held between two heavy bright steel end fittings with plain hexagonal bolts, the lower fitting bolted to a pale grey steel base block, a bright steel torque arm pointing sideways from the upper fitting, a pull rod rising through a small bright steel cylindrical load cell to a pale grey hydraulic cylinder held by an upright frame, with two black hoses, and no people
    Fig · 03 — A tension-torsion strap in its fixture: a pack of thin steel leaves between two end fittings, a torque arm at the top, and a pull rod with a load cell leading up to the cylinder — illustrative render.
    ElementWhat it doesWhat matters
    Reaction framecarries every loada stiff frame with a short load path, so that no load or motion is lost to its give
    Root fixtureholds the specimena fixture that holds a blade root, an element or a plate on its own axis, and that is tried before the test
    Adaptersjoin specimen and actuatoradapters that carry the loads without play and keep them in line
    Tension actuatorapplies the pullan actuator on the axis of the specimen, run in force control so that the pull stays where it is set
    Torsion actuatortwists the specimenan actuator and a torque arm that twist the specimen on top of the held pull
    Bending actuatorsapply flap and lead-lagactuators that bend the specimen in two planes, phased with the twist
    Hydraulic powerfeeds the actuatorsa power pack with margin, clean oil, and filters that are watched
    Controllerruns every channelforce and position channels, phasing between them, spectrum playback, and a record of every run
    Load cells and instrumentsmeasure what was appliedload cells in the load path, displacement and strain, calibrated before the first run
    Stiffness watchends the run (option)a trip on a change in stiffness or displacement, and a check between blocks
    Guards and interlockskeep people clearguards, interlocks and a control room outside
    Testing & documentationprove the facility firsta proving specimen run in steps, every trip tried, and a record the customer can inspect

    The elements that decide the result are the tension actuator and the load cells. The first holds the pull as a force, and the second tells you what was really applied.

    Full specification — expand
    SystemA stiff reaction frame; root fixtures and adapters; a tension actuator, a torsion actuator and bending actuators; servo valves and a hydraulic power pack; load cells, displacement and strain measurement; a controller that runs every channel together with phasing and spectrum playback; a watch on stiffness and displacement; guards and interlocks; and a proving run, a trip check and documentation before handover
    The One IdeaTension changes the twist.
    Why Tension Changes The TwistA tension-torsion strap carries the pull of the blade and twists for pitch, and the pull stiffens it in torsion, so the same twist needs more torque under more tension; a strap twisted with no tension is a different part from one twisted under the pull
    Why The Pull Is Held As A ForceIn the rotor the pull is a force set by the rotor speed. Twisting a strap between fixed ends raises its tension, while a held pull lets the ends draw closer, so the tension channel runs in force control and the twist is driven on top of it
    Standards14 CFR 29.571 covers the fatigue tolerance evaluation of metallic structure in transport category rotorcraft. This page prints none of its requirements, and no edition year. Approval of a part rests with the customer and the authority they name; none is claimed here
    ConfigurationsA blade root tension-torsion facility, a blade root multi-axis facility, and a hub plate test rig
    Scope BoundaryThis page is the rotor hub and blade test facility, which loads a blade root, a strap or a hub plate with the loads of the rotor. It is not a servo-hydraulic fatigue machine, which is a general dynamic test frame for a coupon or a structure (see servo-hydraulic fatigue testing machine), not a shaft torsion fatigue machine, which twists an engine shaft under a thermal gradient (see LP shaft torsion fatigue testing machine) and not an actuator test rig, which proves the actuators that control the pitch (see main rotor actuator test rig). It does not certify a part, and it does not replace the operator's own judgement. No certification or accreditation is claimed here
    StatusNeometrix engineers helicopter rotor hub and blade test facilities to order, and no delivered helicopter rotor hub and blade test facility is claimed.
    04
    Configurations

    One method, three ways to build the facility.

    The method, the frame logic and the trips are shared. What changes is the specimen, how many loads act on it, and how the loads reach it.

    Blade root tension-torsion facility

    A held pull and a twist

    For a blade root or a tension-torsion element: a tension actuator on the axis, a torsion actuator with a torque arm, and a root fixture that holds the part on its own axis.

    Blade root multi-axis facility

    Pull, twist and two bendings together

    For a blade root under the full set of loads: the pull, the twist, and flap and lead-lag bending, run together, phased against one another and following a spectrum.

    Hub plate test rig

    Arms that stand in for the blades

    For a hub plate: arms and adapters that stand in for the blades, with actuators that pull each arm and bend the plate, on the same frame logic and with the same trips.

    And the part that is not equipment at all, yet decides all three: what the loads of the rotor really are. It is taken from the customer's own rotor and its own rules, not from the facility.

    05
    The drawings

    A reference set, drawn as real CAD sheets.

    Two sheets of one reference configuration: the arrangement of a rotor hub and blade test facility with three details, and its control chain with the curves that show how tension changes the twist. They show the frame and the specimen, the actuators and the load cells, and why the pull is held as a force. They carry tags and letters only. Every load, torque, force, angle and size is fixed by design for the customer's duty.

    Reference drawing sheet one, the arrangement and details of a rotor hub and blade test facility. A side elevation shows a reaction frame with a base beam, two end blocks and a gantry, a root fixture clamping the thick end of a tapering blade root specimen, an adapter and a load cell at its free end, a tension actuator on the axis fixed to the right end block, a torque arm pointing down from the adapter with a torsion actuator beside it, and a bending actuator pressing down from the gantry, with the length of the specimen marked by a letter. Detail A shows a pack of thin strap leaves between two end fittings, with the pull and the twist. Detail B shows a hub plate rig in plan, a four-armed plate with one actuator on each arm. Detail C shows the root fixture in section. An item list numbers ten parts. A title block stamped reference configuration, not for construction
    Fig · 04 — Sheet 01, the arrangement: the blade root facility in elevation, the strap pack, the hub plate rig in plan, and the root fixture. Reference configuration, letters only.
    Reference drawing sheet two, the control chain and the curves of a rotor hub and blade test facility. A control chain shows a controller running a tension channel in force control, a torsion channel and a bending channel together, each through a servo valve and an actuator to the specimen, with load cells feeding back what was really applied, a hydraulic power pack feeding every servo valve, and an independent trip that watches the stiffness and the displacement of the specimen and closes the power without asking the controller. Detail A is a computed curve of torque against twist for no pull, some pull and more pull: the same twist needs more torque under more tension. Detail B shows the pull through two cycles of twist: with the ends held still it climbs twice in every cycle, with the force held it stays flat. A title block stamped reference configuration, not for construction
    Fig · 05 — Sheet 02, the control chain and the curves: the force-controlled tension channel, the independent trip, and how tension changes the twist. Reference configuration, tags only.

    Every real facility is drawn for its own specimens, its own loads and its own room. These sheets are the arrangement and the order of working that a project set starts from. Approval of any drawing rests with the customer and the authority they name; none is claimed here.

    06
    Where it is used

    Wherever a rotor part has to be proved first, and trusted in flight afterwards.

    The common thread is a part that carries the whole pull of a blade, a failure that costs far more than the test, and a life that has to be shown and not guessed.

    Rotor makers

    Where blade roots, straps and hub plates are made, and a first article or a batch has to be proved under the loads of the rotor.

    Helicopter builders

    Where a new rotor has to be shown to hold its stiffness and its life before it flies.

    Overhaul and repair bases

    Where a repair scheme or a longer life has to be shown on a blade root or a plate, with the loads of the real rotor.

    Research laboratories

    Where a new material, an elastomer or a composite strap is loaded with the pull and the twist together, to learn how it really behaves.

    07
    Watch

    See it in motion.

    A short walkthrough video of the Rotor Hub and Blade Test Facility.

    08
    FAQ

    Common questions.

    Longer answers, for readers who want the reasoning.

    Q · 01 What does a rotor hub and blade test facility actually do?
    It loads a helicopter blade root, a tension-torsion element or a hub plate the way the rotor loads it in flight, and watches how it stiffens, how it moves and how long it lasts. The specimen is held in a stiff reaction frame by a root fixture, and servo-hydraulic actuators apply the pull, the twist and the bending through adapters. Load cells measure what is applied. A static test finds the stiffness and the strength, a fatigue test counts the cycles to the first crack, and a spectrum test follows a recorded sequence of loads. The facility does not decide which tests a part needs. That comes from the customer's own rotor and rules, and the facility is built, proved and recorded to carry them out.
    Q · 02 Why does tension change the twist?
    Because a tension-torsion strap carries the pull of the blade, and the pull stiffens it in torsion. The strap is a thin pack that joins the blade to the hub, and it twists to let the blade change its pitch. Under a pull the same twist needs more torque, so a strap twisted with no tension, or with the wrong tension, is a different part from the one in the rotor. Its stiffness, the torque it needs and the stress in it all come out differently. So the twist is always measured and cycled under the set tension, and the tension is part of the test and not a setting left to chance.
    Q · 03 Why is the pull held as a force?
    Because in the rotor the pull is a force, set by how fast the rotor turns, and it does not care where the ends of the strap are. When the strap twists, its ends draw closer and the pull stays where it was. A test that holds the ends still gets something else: each twist stretches the outer edges of the strap, so the pull climbs, and it climbs twice in every cycle of twist. The tension actuator therefore runs in force control, with load-cell feedback, and the twist is driven on top of it. This is the step a quick job skips, and it is the one that most often makes a stiffness test disagree with the rotor.
    Q · 04 Why must the loads act together?
    Because in flight the blade root sees the pull, flap bending, lead-lag bending and pitch twist all at once, and they are not independent. The pull changes how the part bends and how it twists, and the bending changes where the stress sits. A part tried under one load at a time proves a different thing from the part in the rotor. So the controller runs every channel together, phases them against one another, and follows the spectrum of the flight. A hub plate adds the pull of every blade, so a hub plate rig loads it through arms that stand in for the blades.
    Q · 05 Is this the same as a servo-hydraulic fatigue machine, a shaft torsion fatigue machine or an actuator test rig?
    No, and the differences are worth stating precisely. The servo-hydraulic fatigue testing machine page covers a general dynamic test frame for a coupon or a structure. The LP shaft torsion fatigue testing machine page covers twisting an engine shaft under a thermal gradient. The main rotor actuator test rig page covers proving the actuators that control the pitch. This page is the facility that loads a blade root, a strap or a hub plate with the loads of the rotor. It does not replace any of them, and it does not claim what they claim a second time.
    Q · 06 Has Neometrix built one of these?
    We would rather answer this plainly than let a page imply otherwise. Neometrix engineers helicopter rotor hub and blade test facilities to order, and no delivered helicopter rotor hub and blade test facility is claimed. What stands behind the offer is adjacent: Neometrix engineers a servo-hydraulic fatigue testing machine (see the servo-hydraulic fatigue testing machine page), a shaft torsion fatigue testing machine that adds axial tension to the twist (see the LP shaft torsion fatigue testing machine page) and a main rotor actuator test rig (see the main rotor actuator test rig page). The load cells, the servo valves, the frame steel and the fasteners are catalogue items, bought in, not invented. What Neometrix engineers is the facility around them: the matching of frame, fixtures and actuators to the specimen, the control, the trips and the proof. So the honest position is that the facility is engineered to order, the neighbouring disciplines are in the building, and the first facility of this exact kind will be built around the customer's own specimens rather than taken off a shelf.
    Q · 07 Which standard applies, and what can the facility not do?
    14 CFR 29.571 covers the fatigue tolerance evaluation of metallic structure in transport category rotorcraft. This page prints none of its requirements, and no edition year: those come from the rule and the authority the customer names. The facility loads a part and records what happened. It does not certify a part, it does not spin a rotor, it does not test the actuators that control the pitch, and it does not replace the operator's own judgement about who is near a loaded specimen and when. This page claims no certification or accreditation. No load, torque, force, frequency or time figure is printed here, and approval of a part rests with the customer and the authority they name; none is claimed here.
    Q · 08 What do you need from us to quote?
    Six things, and most of them describe your specimen rather than the facility. First, the specimen: a blade root, a strap or a hub plate, its size and how it is held. Second, the loads: the pull, the twist and the bending, and how they are phased. Third, the spectrum: a set level, or a recorded sequence, and how many cycles. Fourth, the rate: how many runs in a day, and who will run them. Fifth, the room: what services it has, and what the floor can carry. Sixth, the record: whether a proving run and a test record are needed. From that we come back with a facility concept, a proving plan you can check, and a budgetary price.
    09
    Related

    The neighbouring pages, and how they differ from this one.

    Three neighbours: one is a general test frame, one twists an engine shaft, one proves pitch actuators.

    Browse all Neometrix product lines.

    Get a quotation

    Tell us the specimen,
    and the loads it must carry.

    The projects desk replies within two working days with a facility concept, a proving plan you can check, and a budgetary quotation. Write to [email protected] or use the form.

    Enquire — rotor test facility Capability sheet (PDF) +91 7777 876 876
    ISO 9001 / 14001 ENGINEERED-TO-ORDER CLASS — ROTOR HUB AND BLADE TEST FACILITY DUTY · FRAME AND FIXTURES · ACTUATORS AND POWER · CONTROL · TRIPS · BUILD · PROVE — TENSION CHANGES THE TWIST. ENGINEERED IN NOIDA · INDIA

    Trending Products

    Share This Page

    Engineered To Standards Used In UK, NATO & U.S. Defence Procurement
    DEF STAN (UK MoD)
    NATO STANAG
    RTCA/EUROCAE DO-160
    MIL-SPEC / MIL-STD
    Address
    E-148, Sector-63, Noida, Delhi-NCR, India
    Phone
    Email
    Working Hours
    8:30 AM – 5:30 PM  ·  Mon – Sat
    move to top arrow