200M 400M 200M
RNG: 2.4 KM
BRG: 047°
ALT: 3,200 FT
SPD: 480 KTS
HDG: 012° N
TGT: ALPHA-7
MODE: SEARCH
PWR: NOMINAL
FREQ: X-BAND
STATUS: LOCK
NAVTGTWPNDEFRDRCOM
MIL-STD-1553IFF: ACTIVELINK-16: SYNC
SECTOR: ALPHA
THREAT: CLEAR
RADAR: ACTIVE
TRACK: 6 TGT
LAT 28.6213°N LON 77.3873°E
NX
Neometrix Target Acquired
GB Flag English
English Flag English
Indian Flag हिन्दी
Francis Flag Français
Dutch Flag Deutsch
Spanish Flag Español
Arabic Flag العربية
Russian Flag Русский
Japanese Flag 日本語
Portuges Flag Português
Italian Flag Italiano
Israel Flag עברית
Chinese Flag 中文
Korean Flag 한국어
Thailand Flag ไทย
Vietnamese Flag Tiếng Việt
Indonesia Flag Bahasa Indonesia
Malasia Flag Bahasa Melayu
Kiswahili Flag Kiswahili
Ethiopia Flag አማርኛ
isizulu Flag isiZulu
Hausa Flag Hausa
    Neometrix / Helicopter Transmission Test Rigs / Tail Drive Test Rig / NMX-TGB-108
    NMX-TGB-108 · ENGINEERED-TO-ORDER CLASS — DUTY · BEDPLATE AND DRIVE · LOOP AND CORNER · OUTPUT LOADING · OIL AND TRIPS · BUILD · PROVE

    Tail Drive Test Rig. The corner takes more than torque.

    A tail drive test rig proves a tail gearbox or an intermediate gearbox of a helicopter on the ground: it drives the gearbox, loads it and watches how it runs, how hot it gets and what its oil carries. A tail gearbox turns the power through a corner on its way to the tail rotor. Neometrix engineers the rig as a whole: the bedplate, the loop, the output loader, the oil, the trips and the proof.

    So the rig has to know that the corner takes more than torque, put the thrust and the bending on the output with the torque, and put the corner back when it closes a loop.

    A helicopter tail gearbox test rig on a plain white studio background, seen from above: a pale grey L-shaped steel bedplate whose two arms meet at a right angle, a large black electric motor on one arm joined through couplings and a bright steel torquemeter to a pale grey cast right-angle gearbox standing at the corner, a bright steel shaft running from the gearbox along the other arm through a square steel loading head with two pale grey hydraulic cylinders to a second black electric motor, black hoses to a small manifold block, and no people
    Fig · 01 — A tail gearbox test rig on an L-shaped bedplate: a motor and a torquemeter on one arm, the gearbox at the corner, and the output shaft running along the other arm through a loading head with two cylinders — illustrative render.
    The torque
    goes round a loopso the drive pays only the losses
    The corner
    is in the loopput back by a gearbox, an angle drive or a belt
    The output
    takes thrust and bendingas the tail rotor puts them on it
    The oil
    and the chips are watchedthe run ends on a rise
    Status
    engineered to orderno delivery is claimed
    ISO 9001ISO 1400114 CFR 29.923 reference for rotor drive system endurance tests
    01
    Overview

    What a tail gearbox test has to get right, and what goes wrong when it does not.

    Because torque is the easy load to apply, and the loads that come with the corner are the part that decides.

    Two helicopter tail drive gearboxes side by side on a pale grey mounting plate on a plain white studio background: on the left a compact pale grey cast right-angle gearbox with an input shaft pointing left and an output shaft pointing up, a round inspection cover, a small brass drain plug and a black chip detector body; on the right a slightly larger pale grey cast angled gearbox whose output flange points up and to the right, with a round inspection cover and a black chip detector body, and no people
    Fig · 02 — A right-angle gearbox and an angled gearbox side by side: the first turns the shaft through a right angle, the second through an oblique angle — illustrative render.

    The corner takes more than torque.

    What the rig is for

    It proves a tail gearbox or an intermediate gearbox on the ground. It runs the gearbox in, loads it, runs it for a long time, and records how it behaves, so that a fault shows up on a bedplate and not out on the tail.

    Why the corner takes more than torque

    The tail drive runs from the main gearbox by a long, thin shaft to an intermediate gearbox, which turns it through an angle, and on to a tail gearbox, which turns it through a right angle to the tail rotor. A spiral bevel pair does the turning. As the torque rises, the pair pushes its gears apart and along their shafts, so the bearings and the case carry more than the torque itself.

    Why the output takes thrust and bending

    The tail rotor does not only turn the output shaft. Its thrust pulls along the shaft, and its flapping and its in-plane forces bend the shaft out at the end, past the bearings. A force out at the end of an overhung shaft is multiplied at the nearer bearing, so that bearing carries more than the force itself. A rig that applies torque alone leaves all of this out.

    Why the loop must put the corner back

    A closed loop recycles the power, so the drive pays only the losses. But a gearbox that turns the power through a corner cannot be looped along a straight line. The loop has to turn the power back again, with a second gearbox, with angle drives or with belt drives, or the load is applied by a second motor on the output.

    Why the shaft between is part of the test

    The intermediate gearbox, the tail shaft and the tail gearbox do not vibrate one at a time. They vibrate together, as one coupled system. So the rig carries a shaft that stands in for the real one, with the right stiffness and mass, and the resonances are found with it in place.

    What the tests are

    A functional run proves that the gearbox turns, how it runs in, how hot it gets, whether it leaks and how it sounds. A load run puts the torque, the thrust and the bending on it together. An endurance run does that for a long time, and the record is kept.

    Why the oil is watched

    A tail gearbox may be splash lubricated, and its mesh both rolls and slides. So the oil, its temperature and the chips it carries tell what is going on inside. The rig watches all three and ends the run on a rise.

    Why a tail rig is not for every job

    It is not a main gearbox rig, which circulates the power of a main gearbox and hangs the lift and the moments of the rotor on it. It is a lighter rig for a lighter box that turns a corner. The duty states the gearbox, the loads and the hours, and the rig is built for that.

    02
    The method

    Duty, bedplate and drive, loop and corner, output loading, oil and trips, build and prove.

    Six steps in a fixed order. The output loading and the trips are the two that a quick job skips.

    1 · Duty

    The gearbox, its loads, its speeds, the hours of the runs and the tests are noted, with the room the rig goes in and the services it has.

    2 · Bedplate and drive

    The bedplate, the drive motor and the speed stage are matched to the gearbox, so that the shafts stay in line and nothing on the bedplate gives under load.

    3 · Loop and corner

    The torque loop is laid out so that the corner is put back, with a second gearbox, angle drives or belt drives, or the load is applied by a second motor on the output.

    4 · Output loading

    An output loader puts the thrust and the bending of the tail rotor on the output shaft with the torque, and a stand-in shaft carries the right stiffness and mass.

    5 · Oil and trips

    The oil system, the temperature, the vibration and the chip detector are watched, and the trips work apart from the controller.

    6 · Build and prove

    The rig is built and aligned, the torquemeters are calibrated, a proving gearbox is run in steps, every trip is tried, and the record goes with the rig.

    Which fault, which safeguard

    What can go wrongWhy it happensWhat the rig does about it
    The tooth contact is wrong under loadthe gears move as the case flexes and the torque risesthe contact is read at a light load and again under torque, with the gearbox held as it is on the aircraft
    The output bearings run hotthe thrust and the bending were left out, so the near bearing was never loadedan output loader that puts them on with the torque, and bearing temperatures that are watched
    The loop does not closethe loop does not turn the power back through the cornera loop laid out with the same corner, and the same ratio, put back by a second gearbox, angle drives or belt drives
    The shaft whirls or the box shakesthe rig shaft does not stand in for the real tail shafta stand-in shaft with the right stiffness and mass, and a run through the critical speeds
    The torque is roughthe loader adds a ripple that the aircraft does not havea smooth loader, and loads put in through the casing where the duty needs it
    The oil starves or foulsa pump, a filter or a seal fails, or a part sheds chipsoil flow, temperature and chips watched, with a trip that ends the run
    A fault runs onthe loaded gearbox is stopped too latetrips on temperature, vibration and chips that work apart from the controller, and a controlled stop that unloads before it stops
    Someone is near a loaded gearboxa guard is opened while the drive is turningguards and interlocks, a control room outside, and a procedure that says nobody stands near a loaded gearbox

    The step people underrate is the output loading. A rig looks the same whether it loads the output with torque alone or with thrust and bending as well.

    03
    Work content

    What the rig contains, element by element.

    Read it as a checklist: a rig missing a row will turn a gearbox, but it will not load it the way the tail rotor does.

    The output loading head of a tail gearbox test rig on a plain white studio background: a pale grey cast right-angle gearbox on a pale grey bedplate, a bright steel shaft rising from its output flange through a square bright steel bearing housing to a round flange at the top, a pale grey U-shaped frame holding one hydraulic cylinder that pushes sideways on the bearing housing through a link and another that pulls the shaft upward from the top of the frame, with black hoses, and no people
    Fig · 03 — The output loading head: a bearing housing on the output shaft, with one cylinder pushing it sideways and another pulling the shaft upward — illustrative render.
    ElementWhat it doesWhat matters
    Bedplateholds everything in linea stiff bedplate on which the shafts stay in line under load, with a mounting for the gearbox as it is mounted on the aircraft
    Drive motor and speed stageturns the gearboxa motor and a stage matched to the speed of the gearbox, with a smooth torque
    Torque looprecycles the powera loop that puts the corner back, with a second gearbox, angle drives or belt drives, so that the drive pays only the losses
    Torquemetersmeasure the torquemeters in the shafts of the loop, calibrated before the first run
    Output loaderputs the tail rotor loads onactuators that put the thrust and the bending on the output shaft with the torque, phased with it
    Stand-in tail shaftcarries the couplinga shaft with the stiffness and the mass of the real one, run through the critical speeds
    Oil conditioning skidkeeps the oil rightoil at the right temperature and cleanliness, with flow and pressure measured, and a run-dry option
    Instrumentswatch the gearboxtemperatures, vibration and speed, measured on the case and at the bearings
    Chip detection and tripsend the runa chip detector, and trips on temperature, vibration and chips that work apart from the controller
    Controller and data acquisitionrun the test and record ita controller that holds the loads and the speed, a record that resolves the gear mesh, and a log of every run
    Guards and interlockskeep people clearguards, interlocks and a control room outside
    Testing & documentationprove the rig firsta proving gearbox run in steps, every trip tried, and a record the customer can inspect

    The elements that decide the result are the output loader and the trips. The first puts on the loads that torque alone leaves out, and the second ends the run before a fault does the damage.

    Full specification — expand
    SystemA bedplate; a drive motor with a speed stage; a torque loop that puts the corner back, with angle gearboxes or belt drives; torquemeters; an output loader for thrust and bending; a stand-in for the tail shaft; an oil conditioning skid; instruments, chip detection and trips; a controller and data acquisition; guards and interlocks; and a proving run, a trip check and documentation before handover
    The One IdeaThe corner takes more than torque.
    Why The Corner Takes More Than TorqueA bevel pair pushes its gears apart and along their shafts as the torque rises, and the tail rotor pulls along the output shaft and bends it out at its end, past the bearings, so the near bearing carries more than the load itself; a rig that applies torque alone leaves most of this out
    Why The Loop Must Put The Corner BackA closed loop recycles the power so that the drive pays only the losses. A right-angle gearbox turns the power through a corner, so the loop has to turn it back again, with a second gearbox, angle drives or belt drives, or the load is applied by a second motor on the output
    Standards14 CFR 29.923 covers the endurance tests of the rotor drive system of transport category rotorcraft. This page prints none of its requirements, and no edition year. Approval of a gearbox rests with the customer and the authority they name; none is claimed here
    ConfigurationsAn intermediate gearbox rig, a tail gearbox rig, and a combined tail drive rig
    Scope BoundaryThis page is the tail drive test rig, which proves the lighter gearboxes of the tail drive, the ones that turn the power through a corner. It is not a main gearbox rig, which circulates the power of a main gearbox (see helicopter main gearbox load test rig), not a gearbox test bench, which is a general production test skid for industrial gearboxes (see gear box test bench) and not a rotor dynamics rig, which measures critical speeds and unbalance response (see rotor dynamics test facility). It does not certify a gearbox, and it does not replace the operator's own judgement. No certification or accreditation is claimed here
    StatusNeometrix engineers helicopter tail and intermediate gearbox test rigs to order, and no delivered helicopter tail and intermediate gearbox test rig is claimed.
    04
    Configurations

    One method, three ways to build the rig.

    The method, the oil and the trips are shared. What changes is which gearbox is under test, how many corners the loop has to put back, and what is put on the output.

    Intermediate gearbox rig

    A turn through an angle

    For the gearbox that turns the tail shaft through an angle: a loop laid out with the same angle, by angle drives or by belt drives, and a stand-in shaft on each side.

    Tail gearbox rig

    A right-angle corner and a loaded output

    For the gearbox that turns the power to the tail rotor: a loop that puts the right-angle corner back, and an output loader that puts the thrust and the bending on the output shaft.

    Combined tail drive rig

    Both gearboxes and the shaft between

    For the whole tail drive: both gearboxes with the shaft that joins them, in one loop, so that the coupled vibration of the two gearboxes and the shaft is found with all three in place.

    And the part that is not equipment at all, yet decides all three: what the tail rotor really puts on the gearbox. It is taken from the customer's own helicopter and its own rules, not from the rig.

    05
    The drawings

    A reference set, drawn as real CAD sheets.

    Two sheets of one reference configuration: the arrangement of a tail drive test rig with three details, and its oil and protection chain with the curves that show why the corner takes more than torque. They show the bedplate and the loop, the output loader and the oil, and why the shaft between the gearboxes is part of the test. They carry tags and letters only. Every torque, speed, power, force, angle and size is fixed by design for the customer's duty.

    Reference drawing sheet one, the arrangement and details of a tail drive test rig. A plan shows the tail gearbox rig on an L-shaped bedplate: a drive motor and a torquemeter on the first arm, the tail gearbox under test at the corner, its output shaft running along the second arm through an output loading head with a radial actuator and a thrust actuator to a loading motor, and an oil skid below with its oil line drawn dashed, with the lengths of the two arms marked by letters. Detail A shows the bevel pair in section, pushed apart as the torque rises. Detail B shows the overhung output shaft with its near and far bearings, the force at the end and the two reactions. Detail C shows the intermediate gearbox, where two shafts meet at an angle. An item list numbers ten parts. A title block stamped reference configuration, not for construction
    Fig · 04 — Sheet 01, the arrangement: the tail gearbox rig in plan, the bevel pair, the overhung output shaft and the intermediate gearbox angle. Reference configuration, letters only.
    Reference drawing sheet two, the oil and protection chain and the curves of a tail drive test rig. An oil chain shows a reservoir, a pump, a filter, a cooler and a flow transmitter feeding the gearbox under test, with the oil returning to the reservoir, and a temperature sensor, a chip detector and a vibration probe on the gearbox; an independent trip takes the flow, the temperature, the chips and the vibration and stops the drive and unloads the output loader without asking the controller. Detail A is a computed plot of the bearing reactions of an overhung output shaft against the overhang: the near bearing carries more than the force itself. Detail B is a computed plot of the resonance of two gearboxes joined by a shaft against the stiffness of the shaft: a rig shaft that is too stiff moves the resonance up. A title block stamped reference configuration, not for construction
    Fig · 05 — Sheet 02, the oil and protection chain and the curves: the independent trip, the near bearing, and the shaft between the gearboxes. Reference configuration, tags only.

    Every real rig is drawn for its own gearbox, its own loads and its own room. These sheets are the arrangement and the order of working that a project set starts from. Approval of any drawing rests with the customer and the authority they name; none is claimed here.

    06
    Where it is used

    Wherever a tail drive gearbox has to be proved first, and trusted on the tail afterwards.

    The common thread is a gearbox that cannot be inspected in flight, a tail rotor that the helicopter cannot do without, and a life that has to be shown and not guessed.

    Helicopter builders

    Where a new tail drive has to be run in and loaded before it goes on an aircraft.

    Gearbox makers

    Where a gearbox is made and a first article or a batch has to be proved under torque, thrust and bending.

    Overhaul bases

    Where an overhauled gearbox has to be run and checked, with its oil and its chips watched, before it returns to the aircraft.

    Research laboratories

    Where the coupled vibration of the gearboxes and the shaft, or a new lubricant, has to be studied on a real tail drive.

    07
    Watch

    See it in motion.

    A short walkthrough video of the Tail Drive Test Rig.

    08
    FAQ

    Common questions.

    Longer answers, for readers who want the reasoning.

    Q · 01 What does a tail drive test rig actually do?
    It proves a tail gearbox or an intermediate gearbox of a helicopter on the ground. The gearbox is mounted on a bedplate as it is mounted on the aircraft, driven through a torque loop, and loaded with the torque, the thrust and the bending that the tail rotor puts on it. Torquemeters measure the torque, instruments watch the temperatures and the vibration, and the oil, its temperature and its chips are watched. A functional run proves that it turns and runs in, a load run puts the loads on together, and an endurance run does that for a long time. The rig does not decide which tests a gearbox needs. That comes from the customer's own helicopter and rules, and the rig is built, proved and recorded to carry them out.
    Q · 02 Why does the corner take more than torque?
    Because a gearbox that turns the power through a corner is a pair of bevel gears, and a bevel pair pushes its gears apart and along their shafts as the torque rises. The bearings and the case carry those forces as well as the torque. Out at the tail rotor end, the rotor pulls along the output shaft and bends it, past the bearings, and a force out at the end of an overhung shaft is multiplied at the nearer bearing. So the near bearing carries more than the force itself. A rig that applies torque alone loads none of this, and a gearbox that passes such a rig can still fail on the tail.
    Q · 03 Why must the loop put the corner back?
    Because a closed loop only closes if the power can go round it. A rig for a straight-through gearbox can be looped along a line. A gearbox that turns the power through a corner cannot, because the power leaves it at an angle to where it came in. The loop therefore has to turn the power back again: with a second gearbox, with angle drives, or with belt drives that make up for the angle and the ratio. The drive then pays only the losses. Where a loop is not wanted, a second motor on the output can load the gearbox instead, and the power is returned to the supply.
    Q · 04 Why does the shaft between the gearboxes matter?
    Because the intermediate gearbox, the long thin tail shaft and the tail gearbox do not vibrate one at a time. They vibrate together, as one coupled system, and each one changes how the others respond. A rig that runs a gearbox with a short stiff shaft of its own finds the resonances of that shaft, not of the tail drive. So the rig carries a shaft that stands in for the real one, with the right stiffness and mass, and the critical speeds are found with it in place. Where the question is the whole tail drive, a combined rig puts both gearboxes and the shaft in one loop.
    Q · 05 Is this the same as a main gearbox rig, a gearbox test bench or a rotor dynamics rig?
    No, and the differences are worth stating precisely. The helicopter main gearbox load test rig page covers circulating the power of a main gearbox and hanging the lift and the moments of the rotor on it. The gear box test bench page covers a general production test skid for industrial gearboxes. The rotor dynamics test facility page covers measuring the critical speeds and the unbalance response of rotor-bearing systems. This page is the rig for the lighter gearboxes of the tail drive, which turn the power through a corner. It does not replace any of them, and it does not claim what they claim a second time.
    Q · 06 Has Neometrix built one of these?
    We would rather answer this plainly than let a page imply otherwise. Neometrix engineers helicopter tail and intermediate gearbox test rigs to order, and no delivered helicopter tail and intermediate gearbox test rig is claimed. What stands behind the offer is adjacent: Neometrix engineers a helicopter main gearbox load test rig (see the helicopter main gearbox load test rig page), a gearbox test bench (see the gear box test bench page) and a rotor dynamics test facility (see the rotor dynamics test facility page). The drive motors, the torquemeters, the couplings, the slave gearboxes, the chip detectors and the data acquisition hardware are catalogue items, bought in, not invented. What Neometrix engineers is the rig around them: the bedplate, the loop, the output loader, the oil and the protection. So the honest position is that the rig is engineered to order, the neighbouring disciplines are in the building, and the first rig of this exact kind will be built around the customer's own gearbox rather than taken off a shelf.
    Q · 07 Which standard applies, and what can the rig not do?
    14 CFR 29.923 covers the endurance tests of the rotor drive system of transport category rotorcraft, which includes gearboxes and shafting. This page prints none of its requirements, and no edition year: those come from the rule and the authority the customer names. The rig loads a gearbox and records what happened. It does not certify a gearbox, it does not test a whole rotor drive with the engines, and it does not replace the operator's own judgement about who is near a loaded gearbox and when. This page claims no certification or accreditation. No torque, speed, power, force or time figure is printed here, and approval of a gearbox rests with the customer and the authority they name; none is claimed here.
    Q · 08 What do you need from us to quote?
    Six things, and most of them describe your gearbox rather than the rig. First, the gearbox: which one, and how it is mounted on the aircraft. Second, the loads: the torque, the thrust and the bending, and how they vary. Third, the speeds: the running speeds, and the critical speeds of the shaft to be stood in for. Fourth, the hours: the length of the runs, and how many in a day. Fifth, the room: what services it has, and what the floor can carry. Sixth, the record: whether a proving run and a test record are needed. From that we come back with a rig concept, a proving plan you can check, and a budgetary price.
    09
    Related

    The neighbouring pages, and how they differ from this one.

    Three neighbours: one proves the main gearbox, one is a general test skid, one measures rotor dynamics.

    Browse all Neometrix product lines.

    Get a quotation

    Tell us the gearbox,
    and the loads it must carry.

    The projects desk replies within two working days with a rig concept, a proving plan you can check, and a budgetary quotation. Write to [email protected] or use the form.

    Enquire — tail drive rig Capability sheet (PDF) +91 7777 876 876
    ISO 9001 / 14001 ENGINEERED-TO-ORDER CLASS — TAIL DRIVE TEST RIG DUTY · BEDPLATE AND DRIVE · LOOP AND CORNER · OUTPUT LOADING · OIL AND TRIPS · BUILD · PROVE — THE CORNER TAKES MORE THAN TORQUE. ENGINEERED IN NOIDA · INDIA

    Trending Products

    Share This Page

    Engineered To Standards Used In UK, NATO & U.S. Defence Procurement
    DEF STAN (UK MoD)
    NATO STANAG
    RTCA/EUROCAE DO-160
    MIL-SPEC / MIL-STD
    Address
    E-148, Sector-63, Noida, Delhi-NCR, India
    Phone
    Email
    Working Hours
    8:30 AM – 5:30 PM  ·  Mon – Sat
    move to top arrow